Carrier QHC & QHF Error Codes Explained (E1, E3, F1, P0 and more)
Share
Carrier QHC and QHF split systems (indoor units 42QHC / 42QHF, outdoor units 38QHC / 38QHF) show a fault code on the indoor display, or flash the Operation and Timer lights, when something goes wrong. This guide lists the common codes from Carrier's service information for these ranges, what each one means, and the part that is usually at fault.
Safety first: these units run on mains power, and the outdoor inverter board holds a high-voltage charge after it is switched off. Diagnosis and repairs should be done by a licensed electrician or refrigeration and air conditioning technician.
First step for any code
Switch the unit off at the isolator, wait at least 2 minutes, and switch it back on. If the code clears and doesn't return, it may have been a one-off. If it comes back, use the tables below.
Indoor unit codes
| Code | Lamp flashes | Meaning | Usually check / replace |
|---|---|---|---|
| E0 | 1 | Indoor EEPROM (memory) error | Indoor main PCB |
| E1 | 2 | Indoor / outdoor communication error | Interconnecting wiring, then outdoor and indoor main PCBs (see below) |
| E2 | 3 | Zero-crossing signal error | Indoor main PCB |
| E3 | 4 | Indoor fan speed out of control | Indoor fan motor, then indoor PCB |
| E4 | 5 | Room temperature sensor (T1) open or short | Room temperature sensor |
| E5 | 6 | Evaporator coil sensor (T2) open or short | Indoor coil (pipe) sensor |
| EC | 7 | Refrigerant leak detected | Leak test and re-gas by a licensed technician |
Outdoor unit codes
| Code | Meaning | Usually check / replace |
|---|---|---|
| F0 | Operating current protection | Supply, airflow and condenser cleanliness, then outdoor PCB |
| F1 | Outdoor ambient sensor (T4) open or short | Outdoor ambient sensor |
| F2 | Condenser coil sensor (T3) open or short | Outdoor pipe sensor |
| F3 | Compressor discharge sensor (T5) open or short | Discharge temperature sensor |
| F4 | Outdoor EEPROM (memory) error | Outdoor main PCB |
| F5 | Outdoor fan speed out of control | Outdoor fan motor, then outdoor PCB |
| P0 | IPM / inverter module over-current protection | Outdoor inverter board, then compressor |
| P1 | Over- or under-voltage protection | Mains supply, then outdoor PCB |
| P4 | Inverter compressor drive error | Outdoor inverter board, then compressor |
Code lists can vary slightly between model years, so check the label or manual on your unit if a code isn't listed here.
The E1 fault: why both boards are often the answer
E1 means the indoor unit has stopped hearing back from the outdoor unit. Carrier's service flow is to check the interconnecting wiring and the signal voltage across the outdoor S and N terminals first, then replace the outdoor main PCB, then the indoor main PCB if the fault remains.
From our own experience servicing Carrier QHC and QHF systems, a persistent E1 has often needed both the indoor and the outdoor main PCBs replaced. The communication circuit runs through both boards, and replacing only one can leave the fault in place, meaning a second call-out. If the wiring checks out, it is worth having both boards on hand before the job.
Find your replacement part
- Indoor and outdoor control boards and PCBs: for E0, E1, E2, F4, P0, P1 and P4
- Indoor and outdoor fan motors: for E3 and F5 (see also how to diagnose a faulty fan motor)
- Temperature sensors: for E4, E5, F1, F2 and F3
Every listing shows the Carrier part number. Match it to the label on the board or part in your unit before ordering. Shipped Australia-wide.